เม็ดบีด LED Multispectral Sun Simulators. LED module Simulator.ไฟ LED แบบเต็มสเปกตรัม โทร: +86-0755-81707311 อีเมล: hehualan@chyingfeng.com

เกี่ยวกับ ติดต่อ |

High-Power LED Emitter Selection Guide for 300–1200nm Full-Vehicle Solar Simulators: Spectral Matching, การจัดการความร้อน & Engineering Implementation - LED Solar Simulator โมดูลบอร์ด PCBA 200-1750Nm

High-Power LED Emitter Selection Guide for 300–1200nm Full-Vehicle Solar Simulators: Spectral Matching, การจัดการความร้อน & Engineering Implementation

How to Select High-Power LEDs for a 300–1200 nm Solar Simulator

A specification guide for light-engine integrators and whole-vehicle solar simulation chamber builders

Prepared for publication on the Heyi Light Control corporate website · Product line: LED solar simulator light engines and OEM/ODM high-power LED emitters

Publishing metadata Suggested URL slug: /technology/300-1200nm-solar-simulator-led-selection/ Meta title: 300–1200 nm Solar Simulator LED Selection Guide Meta description: How to select high-power LEDs for a 300–1200 nm solar simulator: the six IEC 60904-9:2020 bands, package choice, thermal and binning limits, and a procurement checklist. Primary keywords: solar simulator LED, 300-1200nm LED solar simulator, high power LED for solar simulator, ไออีซี 60904-9 คลาสเอ+, LED solar simulator manufacturer Recommended schema: TechArticle + FAQPage


Quick answer: the six decisions that determine whether your simulator reaches Class A+

If you only read one section, read this one.

  1. Plan the LED set against the six IEC 60904-9:2020 spectral bands — 300–470, 470–561, 561–657, 657–772, 772–919 and 919–1200 nm — not against the older 400–1100 nm scheme, whose band shares were unequal. Each of the six bands carries roughly the same share of AM1.5G irradiance (16.6–16.7%), so each band needs its own radiometric budget.
  2. Count channels, not just watts. A practical LED engine uses 18–30 independently driven channels: 2–4 peak wavelengths per band. The 300–470 nm band is the most demanding because LED emission bandwidth scales with wavelength — a 400 nm emitter is only ~40 nm wide, a 1000 nm emitter is ~100 nm wide.
  3. Convert irradiance into radiant flux before you talk to any supplier. Radiant flux = target irradiance × illuminated area. Everything downstream — die count, package type, cooling, driver current, cost — follows from that number, not from a datasheet’s nominal “1 W”.
  4. Choose the package by thermal path, not by footprint. เซรามิค 3535/5050 for high-flux channels; COB where single-point colour mixing matters; avoid epoxy-lensed through-hole parts in the high-UV channels.
  5. Specify wavelength bins of 5 nm or tighter and demand the junction-temperature wavelength coefficient. An A+ spectral match certified at 25 °C will drift out of tolerance on a hot array if you mix wide bins or ignore thermal shift.
  6. For whole-vehicle chambers, decide up front how you handle the 1200–4000 nm tail. AM1.5G integrates to 1000.4 W/m² across 280–4000 nm (ASTM G173). A 300–1200 nm LED engine matches the photovoltaic-relevant window, but it does not reproduce the long-wave infrared thermal load that DIN 75220 style chambers also characterise.

Why 300–1200 nm is the correct design window in 2026

The third edition of IEC 60904-9, published in 2020, changed how a simulator’s spectrum is judged. The older edition assessed spectral match from 400 ถึง 1100 NM. Edition 3 assesses 300 ถึง 1200 NM, because modern cell architectures — perovskite–silicon tandems, ฮจต, CIGS, CdTe — respond further into the blue and the near infrared than plain crystalline silicon.

Two consequences matter for an LED buyer:

  • The bands were redrawn. Six bands of near-equal irradiance share replaced the older six bands of unequal share.
  • A new top class appeared. Class A+ is roughly twice as tight as Class A on all three criteria, and it can only be claimed if the simulator is evaluated across 300–1200 nm.

ไออีซี 60904-9:2020 classification thresholds

ClassMinimum range evaluatedSpectral match, all bandsSpatial non-uniformityShort-term instability (โรคติดต่อทางเพศสัมพันธ์)Long-term instability (LTI)
A+300–1200 nm87.5–112.5%1%0.25%1%
อัน400–1100 นาโนเมตร75–125%2%0.5%2%
บี400–1100 นาโนเมตร60–140%5%2%5%
ค400–1100 นาโนเมตร40–200%10%10%10%

The six bands and their AM1.5G share

BandWavelength intervalShare of AM1.5G irradiance (300–1200 nm window)
1300–470 nm16.61%
2470–561 nm16.74%
3561–657 nm16.67%
4657–772 nm16.63%
5772–919 nm16.66%
6919–1200 nm16.69%

Two reporting metrics introduced in edition 3 are not yet part of the class letter, but they are the fastest way to separate a genuinely good LED engine from one that games the band ratios:

  • Spectral coverage (สพีซี) — the share of 300–1200 nm where the simulator emits at least 10% of the reference irradiance. Higher is better.
  • Spectral deviation (เอสพีดี) — the total absolute departure from AM1.5G. Lower is better.

An LED array can pass Class A+ on band ratios while leaving visible holes inside a band, because a single strong emitter can supply a whole band’s irradiance from a narrow slice of it. SPC and SPD expose exactly that failure mode. When you write a purchase specification, put SPC and SPD in it.


Step 1 — Build the wavelength plan before choosing any part number

Do not start from a catalogue. Start from the band table, and give every band a channel budget.

The governing physical constraint is LED linewidth: full-width at half-maximum is typically about 10–20% of the peak wavelength. อัน 385 nm UVA emitter is narrow; a 1050 nm NIR emitter is broad. This means the short-wave bands need more, narrower emitters and the long-wave bands can be filled with fewer, broader ones.

Reference wavelength plan for a 300–1200 nm engine

BandTypical peak wavelengths to combineช่องNotes for procurement
300–470 nm365, 385, 405, 420, 450 NM4–6Highest technical risk. Deep-UV flux and package reliability dominate. Quartz optics, ceramic substrate, no epoxy in the optical path.
470–561 nm470, 490, 505, 530 NM3–4Blue–cyan fill matters for the 470 nm band edge.
561–657 nm570, 590, 617, 630 NM3–4Amber/red gap here is a common cause of low SPC.
657–772 nm660, 680, 700, 730 NM3–4730 nm is essential for the 772 nm edge.
772–919 nm780, 810, 850, 880 NM3–4Cheap, efficient, high-flux; good place to put redundancy.
919–1200 nm940, 970, 1050, 1200 NM3–5Must reach a real 1200 nm emitter, not a 1050 nm tail. Silicon detectors fall off near 1100 NM, so plan an InGaAs measurement channel too.

This table is a design reference, not a fixed bill of materials. The exact peak wavelengths follow from your target spectrum, your spectrometer calibration, and the spectral response of the devices under test.

 

รุ่นผลิตภัณฑ์Product sizeColorDominant wavelengthPeak Wavelengthพลังงานแสงแรงดันไฟฟ้าRdiantIntensityHalf-wave widthityIF (MA)Viewing
(มม.)nm/CIEnm/CIEIV(mW)VF(V)(mW/sr)(NM)มุม(º)
min.max.min.max.
HYF50P40D250AG-X4A5.2*5.2*4.0●UVC LED250-260300-35010-12110.411100060
HYF50P40F260AG-X4A5.2*5.2*4.0●UVC LED260-270210-25010-12117.311100060
HYF50E41F270AG-X4A5.2*5.2*4.0●UVC LED270-280450-55010-1220511140060
HYF50P40F280AG-X4A5.2*5.2*4.0●UVB LED280-290280-33010-1299.713100060
HYF50P40F290AG-X4A5.2*5.2*4.0●UVB LED290-300470-52010-12153.313100060
HYF50P40F300AG-X4A5.2*5.2*4.0●UVB LED300-310600-70010-1214213100060
HYF50P40F320AG-X4A5.2*5.2*4.0●UVA LED320-330470-52010-12173.313100060
HYF50K45B350AG-X4A5.2*5.2*4.0●UVA LED345-3551600-18008-9652.810100060
HYF50G45N360AG-X4A5.2*5.2*4.0●UVA LED360-3653500-42006.8-7.635779140060
HYF50X45B365AG-X4A5.2*5.2*4.0●UVA LED365-3705500-65006.8-7.656229200060
HYF50X45B380AG-X4A5.2*5.2*4.0●UVA LED380-3905500-65006.0-6.8557611200060
HYF50X45B395AG-X4A5.2*5.2*4.0●UVA LED395-4005500-65006.0-6.8539813200060
HYB50G45N400AG-X4A5.2*5.2*4.0●UVA LED400-4055000-60006.0-6.8406615200060
HYB50G45N410AG-X4A5.2*5.2*4.0●UVA LED410-4204000-45006.0-6.8344217140060
HYB50G45N420AG-X4A5.2*5.2*4.0●UVA LED420-4304000-45006.0-6.8264617140060
HYB50G45N430AG-X4A5.2*5.2*4.0●UVA LED430-4404000-45006.0-6.8222119140060
HYB50X38B450AG-X4A5.2*5.2*4.0●Visible LED450-460450.47000-80006.4-7.2720220300060
HYB50G45P460AG-X4A5.2*5.2*4.0●Visible LED460-4704592500-30006.0-6.8282520140060
HYB50G45P470AG-X4A5.2*5.2*4.0●Visible LED470-4804672300-28006.0-6.8206225140060
HYB50G45P480AG-X4A5.2*5.2*4.0●Visible LED480-4904791800-22006.0-6.8213324140060
HYB50G45P500AG-X4A5.2*5.2*4.0●Visible LED500-510498.81200-15006.0-6.8143025140060
HYB50G45P520AG-X4A5.2*5.2*4.0●Visible LED520-530514.51200-15006.0-6.8194127140060
HYB50G45P530AG-X4A5.2*5.2*4.0●Visible LED530-540522.6800-10006.0-6.8135830140060
HYB50G45P540AG-X4A5.2*5.2*4.0●Visible LED540-550538.1500-6006.0-6.8186836140060
HYB50G45N550AG-X4A5.2*5.2*4.0●Visible LED550-560541600-7005.2-6.0107435140060
HYB50F45N560AG-X4A5.2*5.2*4.0●Visible LED560-570555.1700-9004.8-5.6229640140060
HYB50E42N580AG-X4A5.2*5.2*4.0●Visible LED580-590584.6200-3004.4-5.231015140060
HYB50E42N590AG-X4A5.2*5.2*4.0●Visible LED590-600595.2350-4504.4-5.291015140060
HYB50G42N600AG-X4A5.2*5.2*4.0●Visible LED600-6106081000-12004.4-5.2200315140060
HYB50G42N610AG-X4A5.2*5.2*4.0●Visible LED610-620615.21000-12004.4-5.2171126140060
HYB50E42P620AG-X4A5.2*5.2*4.0●Visible LED620-630634.11700-20004.4-5.2377817140060
HYB50E42P630AG-X4A5.2*5.2*4.0●Visible LED630-640646.12100-25004.4-5.2542115140060
HYB50E42N660AG-X4A5.2*5.2*4.0●Visible LED655-6652500-30004.4-5.21169617140060
HYB50G42N670AG-X4A5.2*5.2*4.0●Visible LED670-6802500-30004.0-4.81457121140060
HYB50G42N680AG-X4A5.2*5.2*4.0●Visible LED680-6902500-30004.0-4.8910127140060
HYB50G42N700AG-X4A5.2*5.2*4.0●Infrared LED700-7102200-26004.0-4.8146224140060
HYB50X45N720AG-X4A5.2*5.2*4.0●Infrared LED720-7303000-35004.0-4.8196321200060
HYB50E42N730AG-X4A5.2*5.2*4.0●Infrared LED730-7403000-35004.0-4.8213437200060
HYB50G42N740AG-X4A5.2*5.2*4.0●Infrared LED740-7502500-30004.0-4.8126422200060
HYB50E42N750AG-X4A5.2*5.2*4.0●Infrared LED750-7602500-30004.0-4.8178924200060
HYB50G42N760AG-X4A5.2*5.2*4.0●Infrared LED760-7702500-30003.2-4.0171724200060
HYB50G42N780AG-X4A5.2*5.2*4.0●Infrared LED780-7903000-35004.0-4.8192223200060
HYB50G42N800AG-X4A5.2*5.2*4.0●Infrared LED800-8102000-24003.2-4.0187230200060
HYB50G42N810AG-X4A5.2*5.2*4.0●Infrared LED810-8202000-24003.2-4.0198530200060
HYB50G42N820AG-X4A5.2*5.2*4.0●Infrared LED820-8302500-30003.2-4.0202535200060
HYB50E35N850AG-X4A5.2*5.2*4.0●Infrared LED840-8602500-30003.2-4.0159835200060
HYB50G42N880AG-X4A5.2*5.2*4.0●Infrared LED880-8902500-28003.2-4.0156339200060
HYB50G42N900AG-X4A5.2*5.2*4.0●Infrared LED900-9102000-24003.2-4.0146033200060
HYB50G42N910AG-X4A5.2*5.2*4.0●Infrared LED910-9202000-24003.2-4.0116939200060
HYB50G42N920AG-X4A5.2*5.2*4.0●Infrared LED920-9302000-24002.8-3.6136847200060
HYB50E42N940AG-X4A5.2*5.2*4.0●Infrared LED935-9452000-24002.8-3.6206940200060
HYB50E42N950AG-X4A5.2*5.2*4.0●Infrared LED950-9602000-24002.4-3.2238347200060
HYB50G42N970AG-X4A5.2*5.2*4.0●Infrared LED970-9901500-18002.4-3.2248950200060
HYF50H45N1000AG-X4A5.2*5.2*4.0●SWIR LED1000-10202000-24002.4-3.2241645200060
HYF50G42N1020AG-X4A5.2*5.2*4.0●SWIR LED1020-10401500-18002.4-3.2209155200060
HYF50E42N1040AG-X4A5.2*5.2*4.0●SWIR LED1040-10602000-24002.4-3.2246655200060
HYF50E42N1060AG-X4A5.2*5.2*4.0●SWIR LED1060-10802000-24002.4-3.2244050200060
HYF50X42N1080AG-X4A5.2*5.2*4.0●SWIR LED1080-11002000-24002.0-2.8240355200060
HYF50X42N1100AG-X4A5.2*5.2*4.0●SWIR LED1100-11202000-24002.0-2.8234555200060
HYF50G42N1120AG-X4A5.2*5.2*4.0●SWIR LED1120-1140300-4001.6-2.482956140060
HYF50G42N1140AG-X4A5.2*5.2*4.0●SWIR LED1140-1160300-4001.6-2.483665140060
HYF50G42N1160AG-X4A5.2*5.2*4.0●SWIR LED1160-1180300-4001.6-2.481067140060
HYF50X42N1180AG-X4A5.2*5.2*4.0●SWIR LED1180-1200700-9001.6-2.4165066200060
HYF50G42N1200AG-X4A5.2*5.2*4.0●SWIR LED1200-1250300-4001.6-2.482268140060
HYF50G42N1250AG-X4A5.2*5.2*4.0●SWIR LED1250-1300300-4001.6-2.481675140060
HYF50E42N1300AG-X4A5.2*5.2*4.0●SWIR LED1300-1350500-6001.6-2.4142285200060
HYF50G42N1350AG-X4A5.2*5.2*4.0●SWIR LED1350-1400300-4001.6-2.478783140060
HYF50G42N1400AG-X4A5.2*5.2*4.0●SWIR LED1400-1450250-3501.6-2.4595108140060
HYF50G42N1450AG-X4A5.2*5.2*4.0●SWIR LED1450-1500250-3501.6-2.4694115140060
HYF50G42N1500AG-X4A5.2*5.2*4.0●SWIR LED1500-1550180-2201.6-2.4404137140060
HYF50G42N1550AG-X4A5.2*5.2*4.0●SWIR LED1550-1600100-1401.6-2.4341143140060
HYF50G42N1600AG-X4A5.2*5.2*4.0●SWIR LED1600-170080-1201.6-2.4276138140060
HYF50T42N1700AG-X4A5.2*5.2*4.0●SWIR LED1700-1800180-2101.6-2.4531129200060
HYF50T42N1900AG-X4A5.2*5.2*4.0●SWIR LED1870-1930140-1801.6-2.4404109200060

Step 2 — Choose the package by thermal path and optical role

Heyi Light Control supplies 3535 และ 5050 ceramic SMD, high-density COB, 3528 SMD and 3 มม. / 5 mm through-hole emitters across 200–2000 nm, so the selection question is genuinely about which format fits which channel — not about what is available.

PackageBest role in a solar simulatorStrengthsWatch-outs
3535 ceramic SMDWorkhorse high-flux channel, 1–3 W classLow thermal resistance ceramic substrate, tight footprint repeatability, easy to array on MCPCB with predictable pitchSingle emitter per package, so channel count grows; needs good secondary optics for mixing
5050 ceramic SMDHigher-flux channels, multi-die optionsMore die area per footprint, better radiant flux per placementThermal pad design must be respected or junction temperature drifts
High-density COBSingle-point mixing, collimated engine cores, uniformity-critical designs6–16 wavelengths integrated on one board, secondary lens gives seamless mixing with no ghosting, high radiant density per unit areaConcentrated heat load — requires a real cold plate, not a heatsink; per-channel addressability must be designed into the driver
3528 SMDLow-power trim channels, 657–919 nm fillLow cost, small pitch, good for closing narrow spectral gapsLimited flux; not for the main radiometric budget
3 มม. / 5 mm through-holeLegacy instruments, sensor reference lamps, low-flux retrofitsFamiliar footprint, cheap, easy to socket and replaceEpoxy lens degrades under sustained high UV flux — do not use these as the primary 300–470 nm source in a Class A+ engine

A practical architecture is hybrid: COB cores for the visible and NIR bands where mixing uniformity drives the A+ number, discrete 3535/5050 arrays for the UV band and for bands where you want independent tuning, and small 3528 or through-hole parts for gap filling.


Step 3 — Turn irradiance into radiant flux, then into electrical power

This is the step most specification documents skip, and it is where projects fail late.

Radiant flux required (W) = target irradiance (W/m²) × illuminated area (m²)
Electrical power (W)      = radiant flux (W) ÷ wall-plug efficiency of the chosen emitters

Illustrative arithmetic — substitute your own measured values:

  • อัน 0.1 m² test plane (32 cm × 32 ซม.) at 1000 W/m² needs 100 W of optical power.
  • อัน 2 m × 3 m vehicle chamber test plane at 1000 W/m² needs 6,000 W of optical power.
  • At 30% wall-plug efficiency, those become roughly 333 W and 20 kW of electrical input respectively.

Wall-plug efficiency is not a constant. It varies by wavelength — deep-UV and SWIR emitters convert far less efficiently than blue or NIR — and it falls as junction temperature rises. Ask every supplier for measured radiant flux at a stated drive current and stated junction temperature, and build your budget with the worst-case figure, not the marketing number.

That single number determines cooling architecture (passive heatsink vs. forced air vs. liquid cold plate), driver current per channel, and the number of emitters per band.


Step 4 — Lock the thermal design before you lock the spectrum

LED peak wavelength shifts with junction temperature, and the coefficient is material-dependent: InGaN violet and blue devices shift less than AlGaInP amber and red. In a solar simulator this is not a cosmetic issue — a wavelength shift moves irradiance between bands and changes your spectral match ratio.

Three consequences for selection:

  1. Treat thermal resistance as a first-class specification. เซรามิค 3535/5050 packages in the Heyi high-power line are built on high-thermal-conductivity ceramic substrates with thermal resistance below 2.5 K/W; that figure, not the nominal wattage, sets how hard you can drive a channel.
  2. Ask for the measured wavelength-versus-junction-temperature curve for each wavelength family you plan to use, and integrate it into your control model. If a supplier cannot produce the curve, the part is not ready for a Class A+ engine.
  3. Design for thermal equilibrium, not for switch-on. Short-term instability of 0.25% (คลาสเอ+) is not achievable while the array is still warming up. Specify a stabilisation period, and require the driver to hold constant current while the cold plate holds constant temperature.

Step 5 — Demand tight wavelength binning, and bin by channel

Spectral match is computed per band, so binning discipline is where a cheap BOM quietly destroys an expensive calibration.

  • Wavelength bin: 5 nm or tighter for the 300–470 nm band and for any band edge where you are close to tolerance. Wider bins may be acceptable in 772–919 nm, where the band is 147 nm wide and the emitter linewidth is broad.
  • Flux bin: one flux bin per channel, or the drive current per channel has to be trimmed individually at production.
  • Forward voltage bin: narrow Vf bins keep series-connected strings balanced and make constant-current drivers behave predictably.
  • Traceability: every reel should carry wavelength bin, flux bin, Vf bin, lot and LM-80 reference. This is what lets you re-order the same engine two years later and keep the same classification report.

Step 6 — Driver and control architecture

The LED is necessary but not sufficient. Class A+ temporal instability of 0.25% is a system-level number, and it comes from three things:

  • Independent, high-resolution dimming per channel. 16-bit or better resolution, so you can trim a band ratio by a fraction of a percent rather than by a visible step.
  • Optical feedback. A monitoring photodiode per band, or at minimum per band group, closed on the driver. Open-loop current control cannot hold 0.25% over a multi-hour ageing test.
  • Communication and logging. CAN, RS-485 or Ethernet control with a documented register map, so the spectrum recipe, drive currents and calibration date travel with the data. This is also what makes the engine reusable across an AM1.5G pump, a stabilised light-soaking mode, and a variable-spectrum research mode.

Step 7 — Do not buy emitters without a metrology plan

To claim anything under IEC 60904-9:2020 ฉบับ 3, you must measure to 1200 NM. Silicon spectrometers fall off near 1100 NM, so a single-channel Si measurement will silently under-report the top of band 6.

A credible verification chain has three parts:

  1. Spectroradiometer with a silicon plus InGaAs channel, calibrated and traceable, covering 300–1200 nm.
  2. Spatial uniformity mapping at the number of positions your target standard requires (ASTM E927-19 specifies a minimum of 64 positions for the uniformity calculation).
  3. A reference cell or detector for irradiance level, plus a black-panel or equivalent temperature reference for thermal-load work in chambers.

If your supplier’s classification report does not state which edition of the standard it follows, which spectral range was measured, and which detector technology was used above 1100 NM, treat the class letter as unverified.


Whole-vehicle solar simulation chambers: what changes

A whole-vehicle chamber is the same physics at a very different scale, and four constraints change the emitter selection.

1. Area scales the flux budget brutally. อัน 6 m² test plane at 1000 W/m² is 6 kW of optical power. That is an array of hundreds of high-power emitters and tens of kilowatts of electrical input. Efficiency stops being a nice-to-have and becomes the dominant cost line — both capital and running.

2. Uniformity across metres is an optical design problem, not an emitter problem. At 1% ความไม่สม่ำเสมอเชิงพื้นที่, array pitch, mixing distance, collimation and baffling dominate. This is where high-density COB cores with secondary optics earn their cost: a single mixing point with a tailored lens produces a smoother field than a sparse grid of discrete emitters.

3. The spectrum gap is real. DIN 75220 style vehicle ageing work characterises broad-band solar load, and IEC 60068-2-5 Test Sa describes simulated ground-level solar radiation across a broad spectrum. A 300–1200 nm LED engine is the right answer for the photovoltaic-relevant window and for visible/UV material degradation, but the long-wave infrared contribution above 1200 nm has to come from somewhere — either supplementary IR emitters or a hybrid lamp arrangement. Decide this in the architecture phase; retrofitting it later means rebuilding the optical bench.

4. Serviceability decides total cost of ownership. A vehicle chamber may run thousands of hours. Specify socketed or connectorised emitter modules, per-channel fault detection, and a spare-part wavelength bin commitment from the supplier, so a single failed channel can be replaced without recalibrating the whole field.

Heyi Light Control’s OEM/ODM model is built around this: custom wavelength sets from 200 นาโนเมตรถึง 2000 NM, ceramic and COB formats, and ready-to-ship standard wavelengths so that a production line is not held hostage by a single custom run.


Procurement acceptance checklist

Put these twelve items in the purchase order. They are the difference between a simulator that passes on the day of acceptance and one that still passes two years later.

#Item to specifyWhy it matters
1Target IEC 60904-9:2020 ฉบับ, target class per metric (E.G. เอ+เอ+เอ+)Edition 2 and edition 3 classes are not interchangeable
2Peak wavelength and bin width per channel (≤5 nm in short-wave bands)Band ratio tolerance is consumed by bin spread
3Radiant flux at stated drive current and stated junction temperatureNominal wattage is not radiant flux
4Thermal resistance (K/W) and recommended TcSets achievable drive current
5Wavelength temperature coefficient, measuredNeeded for spectral stability modelling
6Spectral coverage (สพีซี) and spectral deviation (เอสพีดี) targetsExposes band-ratio gaming
7Spatial non-uniformity target and measurement position countASTM E927-19 requires ≥64 positions
8Short-term and long-term instability targets and stabilisation timeA+ requires 0.25% โรคติดต่อทางเพศสัมพันธ์
9LM-80 / TM-21 data or an equivalent lumen and radiant flux maintenance curvePredicts recalibration interval
10Driver interface: channels, resolution, feedback, protocol, register mapDetermines whether 0.25% is reachable
11Optical materials in the UV path (quartz vs. polymer)Polymer yellows and shifts the UV band
12Re-order durability: bin commitment, lot traceability, change-notification clauseProtects the classification report over time

Five failure modes that show up after commissioning

  1. The comb spectrum that still passes. A set of narrow emitters can hit every band ratio while leaving visible gaps inside each band. SPC and SPD catch it; a class letter alone does not.
  2. Bin drift on re-order. The second production batch uses a wider wavelength bin, the band ratio moves, and the original classification report no longer applies.
  3. Thermal creep. Junction temperature rises as the cold plate fouls, peak wavelengths shift, and long-duration tests drift out of tolerance while short tests still pass.
  4. UV path degradation. Epoxy or silicone in the 300–400 nm optical path yellows, cutting UV flux and destroying the short-wave bands first.
  5. Metrology blind spot above 1100 NM. The simulator is fine but the measurement is not, so band 6 is reported from a detector that cannot see it.

Eight questions to ask any LED supplier

  1. Which wavelength families do you manufacture, and what is your measured wall-plug efficiency at each?
  2. What is the actual wavelength bin width you can commit to, per family, in writing?
  3. Can you provide a measured peak-wavelength versus junction-temperature curve?
  4. What is the thermal resistance of the package, and what Tc do you recommend at my drive current?
  5. Do you have LM-80 or equivalent long-term radiant flux data, and over what duration?
  6. Which optical materials do you use in the UV path, and how do they age under high flux?
  7. Can you supply a mixed-wavelength COB with 6–16 channels on one board, and what is the die placement tolerance?
  8. What is your change-notification process when a die or phosphor changes?

A supplier who answers all eight in writing is a supplier you can put on a vehicle chamber programme. Heyi Light Control answers them per project, because spectral customisation is the core of the business rather than an exception.


คำถามที่พบบ่อย

What LED wavelengths do I need for a 300–1200 nm solar simulator?

Plan for 18–30 channels grouped into the six IEC 60904-9:2020 bands. Typical peaks are 365/385/405/420/450 NM, 470/490/505/530 NM, 570/590/617/630 NM, 660/680/700/730 NM, 780/810/850/880 nm and 940/970/1050/1200 NM. The short-wave bands need more, narrower emitters because LED linewidth scales with wavelength.

Can an LED simulator reach Class A+?

Yes, on all three metrics, but only if it is evaluated across 300–1200 nm. Class A+ requires spectral match within 87.5–112.5% in every band, spatial non-uniformity of 1%, short-term instability of 0.25% and long-term instability of 1%. The hard parts are the 300–470 nm band and the measurement chain above 1100 NM.

Is 300–1200 nm enough for a whole-vehicle solar simulation chamber?

It is enough for the photovoltaic-relevant window and for visible and UV material degradation, but not for the long-wave infrared thermal load above 1200 nm that DIN 75220 style ageing work also characterises. Decide in the architecture phase whether you supplement with IR emitters or use a hybrid source.

3535 หรือ 5050 or COB — which package should I use?

Use 3535 ceramic for general high-flux channels, 5050 where you need more die area per placement, and high-density COB where single-point mixing and uniformity are the binding constraint. Most real engines are hybrids. Avoid epoxy-lensed through-hole parts as the primary source in the 300–470 nm band.

How many LEDs do I need for 1000 วัตต์/ตรม?

Divide: required radiant flux = 1000 W/m² × illuminated area. อัน 0.1 m² plane needs 100 W of optical power; a 6 m² vehicle chamber plane needs 6,000 W. Then divide by the measured wall-plug efficiency of each wavelength family to get electrical input, and size cooling from there.

Why do spectral coverage and spectral deviation matter if they are not part of the class letter?

Because band ratios average over a band, a narrow but intense emitter can satisfy a whole band while leaving the rest of it dark. SPC and SPD quantify what the class letter hides. A high SPC and a low SPD are the practical definition of a simulator that behaves like sunlight rather than merely scoring like it.

Does wavelength binning really change the classification?

Yes. Spectral match is computed per band, so a ±10 nm bin spread inside a band only 91 nm wide (470–561 nm) consumes a meaningful fraction of the tolerance before any thermal shift is added. Specify 5 nm or tighter in the short-wave bands.

What is the minimum verification setup I need in-house?

A calibrated spectroradiometer covering 300–1200 nm with both silicon and InGaAs channels, a uniformity mapping rig at the position count your target standard requires, and a reference detector for irradiance level. Without the InGaAs channel, band 6 is unverified regardless of what the report says.


Standards and references


About the manufacturer

Heyi Light Control (บริษัท Shenzhen Heyi Heyi Optical Control Co., Ltd.) manufactures high-power LED emitters and spectral modules across 200–2000 nm, including 3535 และ 5050 ceramic SMD, high-density COB, 3528 SMD and 3 มม. / 5 mm through-hole formats. The company supports OEM and ODM programmes with custom wavelength sets, mixed-wavelength COB integration and ready-to-ship standard wavelengths for fast sampling.

For product data, sample requests and spectral customisation enquiries, contact the team through the company’s Alibaba.com storefront: https://led-solarlight.com/

https://hongkongheyi.en.alibaba.com/

All standard thresholds and band shares quoted in this article are taken from the published standards referenced above. Application-specific parameters — thermal resistance, radiant flux and wavelength temperature coefficients — should be confirmed against the current datasheet and test report for the exact part number used in your design.

ก่อน:

ทิ้งการตอบกลับ

ฝากข้อความ